How about a D.I.Y. companion?
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
5 / 5
1 Reveja
rating breakdown
5 Stars | 1 | |
---|---|---|
4 Stars | 0 | |
3 Stars | 0 | |
2 Stars | 0 | |
1 Stars | 0 |
Fits: KAWASAKI , KAWASAKI , KAWASAKI Zephyr 400 RS, KAWASAKI , KAWASAKI
[How is it used?
I bought this as an O-ring where the center axis of the Element meets the round, flat opening lid when replacing the Oil Element on my gpz900r.
The O-ring always retains a nice round shape when removed and is elastic enough to be reused.
Besides, if you remove the Exhaust System and loosen the Element fixing bolt, you can remove this O-ring part without loosing it.
So we buy this as insurance in case of a leak, and if it doesn't leak, we replace it once every two or three times.
How was your experience with it?
OK
How did it compare to other products?
Same as OEM
Please let me know the points that I should pay attention to.
Please note that turning the opening lid separately from the shaft will ruin the seal.View Detail
[How is it used?
At the time of Oil Element replacement in gpz900r, it is arranged to O-ringfor Replacement of the opening part.
In my experience with the Z series, if you drive on the street, have few high temperature runs, and replace the O-ring only once a year, the O-ring has never been worn out or melted and lost its seal.
In other words, I think it can be reused.
However, since OIL replacement also serves as a refreshing change, I will replace this as well.
However, it's a pity that this O-ring was not included in the kit when I bought Element including KIJIMAElement before.
I guess it's a reduction in cost, but if a company owns it, the unit price will be lower, so I would like to see the price be reduced to about 30 yen Plus for us, and replacement parts such as O-rings should be included.
How was your experience with it?
It's obvious.
How did it compare to other products?
No change.
[Points to note]
If you apply a thin layer of Oil with your finger and assemble it, it blends in well and is hard to make assembly mistakes.View Detail
Fits: HONDA VTR250 MC33, HONDA HORNET250 , HONDA CB400T CB250T , HONDA CB400TII CB400T
[How is it used?
The VTR250 that I prepared to start Gymkhana.
I changed the engine oil and the oil filter before I started to run the car because it was too cheap and battered car that I got on Yahoo!
Since the vehicle is not yet assembled, I'm giving it a 3 for now for durability.
Still, it's KIJIMA, and you can trust them〜.
Was the one you received as per Image?
As shown in the image, a complete set of oil seals is required when replacing the Oil Filter.
Was the installation difficult?
You can tell which Seal goes with which by opening it and staring at it.
After reassembling and before tightening, be careful that the seal does not stick out and bite.
How was your experience with it?
As I mentioned above, I haven't gotten it running yet because it doesn't have the security parts on it.
But it's not peeing on the floor, so I guess it's Large durable.
[Was there anything that disappointed you?
There is not. Even if there is, it is the price which can be paid if you endure to buy one MONSTER S2.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
→ Items to be purchased together
Prepare the Oil Filter together.
https://www.webike.net/sd/1907693/View Detail
Purchased for regular replacement.
If it were a little cheaper, I could get a stable replacement...View Detail
?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Grip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Serviço ao cliente
ORDENS
EM FORMAÇÃO
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING